There are more and more ideas in smart home.，therefore，Now many crystal lamps are controlled by switching，To control a variety of colors of crystal lamps。Not only，Many large lumines can remotely control through the remote control，in this way， Avoid many problems“Lazy cancer”Children's shoes，I spent a long time I don't want to start the tangle of the bed for a long time.，Gently press the remote control，But if the crystal lamp switch is faulty，What if I can't use a crystal lamp switch?？The following editor will analyze it， But if the crystal lamp switch is faulty，The reason and maintenance plan provided by the remote control of the crystal lamp switch。
1。 Causes and maintenance methods of crystal lamp switch remote control failure
One。 the reason：Unable to use a crystal light switch remote control。Crystal lamp switch cannot be opened，Remote control does not respond，This is because the power supply is not electrified，Can be repaired by some ways，But the remote control is electricity? Can you send a signal to receive the signal on the lamp?？Non-professionals should be cautious。
B． Maintenance：
1。 Check if the power switch is tripping。
2。 Check if the switch is damaged。
3。 Check if the control line of the crystal lamp is disconnected。
4。 If the above situation is normal，Crystal lamp damage。
2。 Causes and solutions for crystal light switch failures
Shut down，Crystal lamp switch is still open，Since the capacitor is a path to the main electricity AC power，After turning off the switch。Such problems have been answered by others，The switch controlled by the switch can still be turned on by a distributed capacitor at both ends of the switch.。You should think of a solution。however， LEDWork current belongs to the milliamp（depending onLEDtype， A few hundred mAh， This is usedLEDFrequently in the light。Since this distributed capacitor is very small（Means of， Capacitive reactance is very large），Ordinary lighting does not 易彤料理机维修 change significantly，This current flows if you have a handshake，I will not introduce you to organize you with your brain and reply you.，LEDPower supply is also because），This is due to parallel and close to each other during the wiring process.（Usually in the same line）The formed distribution capacitor is caused。
Understanding the reason， Switch off，LEDThe lamp will no longer glow normal， Flashes， and many more），But this is not caused by a power-driven or air rotation switch.。That is，The resulting current is very small（Millian level），however， Distributed capacitor leakage current may resultLEDVisual change（For example, dim light flashes）。This is due to the wire before and after the switch，So the problem is coming，LEDInstead， After fifteen minutes, it will lit again.，The switch does not turn off。This is not a new problem。So-called unchanged changes，Different expressions but root cause is distributed capacitance。
You only need to remove the switch，It seems that the circuit has been completely cut and separated.，Due to distributed capacitance（Switch wiring direction and distribution）No change， The power supply is an alternating current，LEDThere will always be a leakage current in the lamp circuit.，Just the size of the distribution capacitance according to the wiring，Leakage current difference。
In fact， room， Internal and external wiring will form a distributed capacitor（AC electricity， This is a road，Despite the large capacitance reactance），Just this kind of（Very small）Leakage current effect is for traditional electrical appliances，You can't detect its existence，but，LED（Millian level）Light is a replacement。
In addition to the distribution capacitance of external wiring，byLEDComposed of lamps and drive circuits（Multiple）There is also a big difference between。Guess youLEDHappening，It should be that the leakage current after turning off the switch is not enough to make yourLEDBrighten。however， A constant current source（make sureLEDNormal and long life support equipment）Large rectifier filter capacitor inside the circuit，Waiting for a smaller leakage current to make it slowly full，The back circuit can start to loadLEDPower supply，Since the capacity of the capacitor is not sufficient to maintain，therefore，Highlight，LEDBe extinguished，Capacitor slowly enters the next leakage current charging process，So it goes back and forth，normalLEDLightning and extinguishing。
Once there is no good study for a little physics，It is difficult to understand the above。therefore， Master's editor thinks if there is a problem with the light bulb， It is best to buy a store，Remote control of the crystal lamp switch matching the same model。If it is the crystal lamp itself, I suggest youWanshifuLight bubble maintenance merchants to check and repair light bulbs on the platform。
